Jump to content

Meters meters meters


Benson Gravois
 Share

You are about to reply to a thread that has been inactive for 134 days.

Please take a moment to consider if this thread is worth bumping.

Recommended Posts

1 minute ago, Benson Gravois said:

So, does anyone know how to measure a parcel of land. I know that everything in SL is measured in meters. But how do you actually measure?

I usually place out a prim and stretch it to the parameters of the parcel, and then look in the Edit box where the meters are stated.

  • Like 3
  • Thanks 2
Link to comment
Share on other sites

13 minutes ago, Benson Gravois said:

So, does anyone know how to measure a parcel of land. I know that everything in SL is measured in meters. But how do you actually measure?

the smallest landselection you can make is 4x4 meters (16m2) so all parcels are made with these smallest selections 
To measure sizes of sides you can use prims,  or measurement instruments that are for sale at MP, but those aren't needed, if you rezz a prim and stretch it you can read the numbers in the buildtool.

  • Thanks 1
Link to comment
Share on other sites

If it's the total parcel size that's of interest, the "About Land" window's "General" tab has the "Area" of the entire parcel in m².

To measure out the dimensions of a parcel you may not be able to rez on, you can right-click on the parcel and choose "Edit Terrain" which pops up the build tool with the bulldozer terraforming tool selected—but it's okay, you're not going to terraform: the "Select Land" radio button is enabled, so you can drag the mouse over the hunk of land you want to measure and the window's "Parcel Information" includes the area of just the highlighted/selected land. Also, for the actual dimensions, as Alwin says the smallest units of land you can select are 4m x 4m, so count 'em up and multiply by 4m for a linear dimension (or by 16m² each for area).

  • Like 2
Link to comment
Share on other sites

   It's not as if things being metric changes how you measure something. You can use a prim ruler as described above, or you can walk to the edge of the parcel and note your coordinates and then head to the opposite edge and subtract the lower number, and the difference is your parcel width. When you've got your width and depth you simply multiply them, just as you would if you were measuring with yards or feet or chains or furlongs. 

   .. Or you just look at the about land tab and see the parcel size at the bottom of the general tab.

2191901875c91f0da497e8aa36819781.png

  • Like 1
  • Thanks 2
Link to comment
Share on other sites

2 hours ago, BilliJo Aldrin said:

When its zero F. its very very cold, and when its 100 F, its very very hot 😁

   Because the freezing point and boiling point of water .. Isn't? 

  • Like 1
  • Thanks 1
  • Haha 1
Link to comment
Share on other sites

6 hours ago, Zalificent Corvinus said:

What's wrong with Kelvin? 0 K freezing point of Liquid Hydrogen, 273.15 K freezing point of Liquid Di-Hydrogen-Oxide.

 

did you know that di hydrogen oxide is the number one green house gas? It's  responsible for 95% of the green house effect. CO2 at 5% is negligible at best.

We need a concerted international effort to rid the planet of this compound that will surely cause the extinction of all life on earth if left unchecked.

😂

Edited by BilliJo Aldrin
added an emoji
Link to comment
Share on other sites

7 hours ago, Love Zhaoying said:

Plus, the freezing and boiling points change with altitude!

   No. It does, however, change with pressure. And pressure, of course, changes with altitude (assuming you're not in a pressurised environment, such as an aeroplane - although most pressurised cabins don't have 'sea level' pressure, but something comparable to 6,000-8,000 feet - which is why tea brewed on a flight tastes sh!te, as water boils at around 91C at such pressure, but that's a question of thermochemistry rather than pressure or altitude).

  • Like 1
Link to comment
Share on other sites

You are about to reply to a thread that has been inactive for 134 days.

Please take a moment to consider if this thread is worth bumping.

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
 Share

×
×
  • Create New...